Product features
The numbering of the product features refers to the diagram of the power tool on the graphics page.
(1) | Scale for spacing between saw blade and parallel guide |
(2) | Slide carriage |
(3) | Angle guide |
(4) | Carrying handle |
(5) | Label for marking the cutting line |
(6) | Protective cover |
(7) | Riving knife |
(8) | Parallel guide |
(9) | Guide groove for angle guide |
(10) | Saw table extension |
(11) | Saw table expansion |
(12) | Securing nut for the saw blade storage compartment cover and for hanging the push stick |
(13) | Push stick |
(14) | Saw blade storage compartment cover |
(15) | Ring spanner (24 mm; 23 mm) |
(16) | Mounting holes |
(17) | Saw table |
(18) | Clamping handle for saw table expansion |
(19) | Hand wheel |
(20) | Crank for raising and lowering the saw blade |
(21) | Safety flap for the on/off switch |
(22) | Bracket for storing the protective cover |
(23) | Holding clip for storing the angle guide |
(24) | Guide bar of the saw table extension |
(25) | Stop for 45° bevel angle |
(26) | Locking lever for setting the bevel angle |
(27) | Scale for bevel angles |
(28) | Stop for 0° bevel angle |
(29) | Clamping handle for slide carriage |
(30) | V guide groove on the saw table for the parallel guide |
(31) | Adjusting screw for adjusting the clamping force of the parallel guide |
(32) | Table insert |
(33) | Saw blade |
(34) | Profile rail |
(35) | Guide groove for parallel guide |
(36) | Parallel guide storage compartment |
(37) | Hex key (5 mm) |
(38) | Locking screw of the saw table extension |
(39) | "Additional parallel guide" fastening set |
(40) | Chip ejector |
(41) | Dust extraction adapter |
(42) | Cable holder |
(43) | "Saw table extension" fastening set |
(44) | V guide for parallel guide |
(45) | Base plate |
(46) | Clamping lever for riving knife |
(47) | Positioning pins for riving knife |
(48) | Recesses for table insert |
(49) | Clamping lever for protective cover |
(50) | Guide pin for protective cover |
(51) | Clamping handle for parallel guide |
(52) | Additional parallel guide |
(53) | Guide rail for angle guide |
(54) | Knurled screw for fixing the angle guide |
(55) | "Profile rail" fastening set |
(56) | Knurled nut for profile rail |
(57) | Lower saw blade cover |
(58) | Fastening screw of the lower saw blade cover |
(59) | Clamping nut |
(60) | Spindle locking lever |
(61) | Clamping flange |
(62) | Mounting flange |
(63) | Tool spindle |
(64) | Angle indicator (vertical) |
(65) | Locking knob for all mitre angles |
(66) | Mitre angle indicator on the angle guide |
(67) | Adjusting plate |
(68) | Magnifying glass |
(69) | Saw table spacing indicator |
(70) | On button |
(71) | Cross-head screw for setting the 0° stop |
(72) | Screw for bevel angle indicator |
(73) | Cross-head screw for setting the 45° stop |
(74) | Hex socket screws (5 mm) on the front for adjusting the parallelism of the saw blade |
(75) | Hex socket screws (5 mm) on the rear for adjusting the parallelism of the saw blade |
(76) | Screw for saw table spacing indicator |
(77) | Hex socket screws (5 mm) for adjusting the parallelism of the parallel guide |
(78) | Screw for parallel guide spacing indicator |
(79) | Adjusting screws for table insert |
(80) | Bracket for storing the "additional parallel guide" fastening set |
(81) | Holding clip for storing the dust extraction adapter |
(82) | Saw blade storage compartment |
(83) | Bracket for storing the hex key |
(84) | Holding clip for storing the additional parallel guide |